![]() Continue the above steps for the remaining 2 speakers in the daisy-chain.At the next speaker, repeat steps 2 – 7 for the left channel using the white (+) and green (-) leaving the red (+) and black (-) wires intact.Secure these three wires using the provided silicone filled wire nuts, ensuring that NO COPPER is exposed.Combine and twist the red wires from the amplifier, the first satellite and the wire running to the next speaker in a clock-wise motion. Strip off 3/4 inch of insulation on the red and black wires to expose the copper conductor.In this example, we want the first speaker to be connected to the right channel so we cut the red (+) and black (-) wires only. Use a wire tie to keep the wire loop intact and act as a strain relief.Or visit the specific brand of cable stripper’s company website for detailed instructions. The Sonance DSP SR 2-125 amplifier comes preloaded with optimized DSP curves for Patio Series, ensuring full audio performance for your space (SR 2-125 Amplifier included in Patio Series System, SKU 93430). If you are unfamiliar with using a round cable stripper, please go to YouTube and search for videos on ‘Using a Round Cable Stripper’. The system connects in parallel from the 2 channel Sonance SR 2-125 amplifier for easy wiring and setup. Use the round cable stripper to remove the outside protective wire jacket to expose the 4 individual color-coded wires.Starting at the first speaker and every speaker that follows, create a loop of wire approximately 6” in length.Leave the wire attached to the spool until the last speaker has been connected. Pull the 14/4 wire on the spool to the furthest speaker location.When subwoofer is in the ground, ensure that there is roughly 5” of exposed subwoofer enclosure from the surface of the ground to the bottom edge of the canopyĬonnecting the speakers using 14/4 direct burial speaker wire. NOTE: The subwoofer requires a burial space that is about 12” diameter and 11” deep. Once the speakers and subwoofer are laid out in their locations and the wiring is completed per this installation guide, stake or mount the speakers into their final locations and bury the subwoofer in its final location.Run your speaker wire through the trench from the amp to the first speaker location.Be sure to check local codes for trenching limitations. Dig a 4” to 5” trench to run the speaker wires in.Place the 4 satellites and 1 subwoofer in their approximate final locations.Connecting the Speaker Using a 2-Conductor Wire or Low Voltage LIghting Wire. ![]() ![]() Owner’s Manual OUTDOOR AUDIO SYSTEM Sonance 93429 Accessories (21) Active (2) Amp and Port (2) Back Boxes (2) Controllers & Base Stations (7) Cooling (1) Doors (1) Drawers & Shelves (1) Floor Standing/Bookshelf (1) Horn (28) In-Ceiling (87) Loudspeakers (47) Mono / Sub Amps (4) Mulit-Channel (1) Multi-Channel (11) Music Streamer (1) Outdoor & Landscape (9) Pendant (8) Powered (2) Pre-Construction Bracket (26) Pre-Construction Brackets (26) Rocks (7) Satellite Speakers (12) Sound Masking (4) Soundbars (40) Speaker Mounts (17) Speakers (2) Stereo (32) Subwoofers (14) Turntables (1) Volume Controls (10) Wireless (1) Wireless Speakers (15)Ģ Channel (33) 4 Channel (2) 1 Channel (4) 1 Space (1) 10" (11) 11 Channel (2) 12 Channel (2) 12" (15) 13 Channel (1) 15" (4) 16 Channel (1) 18" (1) 21 Space (1) 3" (1) 3.5" (2) 4" (19) 4.5" (3) 5 Channel (2) 5" (1) 5.25" (13) 5.5" (1) 6 Channel (1) 6" (11) 6.2" (1) 6.Sonance 93429 Patio Series 4.1 Outdoor Audio System - Use Manual - Use Guide PDF.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |